How To Change Water Filter On LG Fridge

If you have an LG fridge with a water dispenser and ice maker, you need to change the water filter regularly to ensure you get clean and fresh water. The water filter helps remove contaminants, such as chlorine, lead, and bacteria, from the water supply. Changing the water filter on your LG fridge is not difficult and you can do it yourself in a few minutes. Here’s how to do it step by step.

To change the water filter on your LG fridge, you need to turn off the water valve, locate the water filter housing behind the left side refrigerator door, and remove the old water filter by pressing the push button and pulling it down.

Then, you need to install the new water filter by removing the protective cover, pushing it into the manifold hole, and rotating it up. You may also need to tilt up and pull out the top shelf to access the filter compartment.

How to Turn Off the Water Valve

The water valve connects your refrigerator to the waterline. Turn it off in order to stop the flow of water to your refrigerator. You can then proceed to remove the old water filter.

• Locate the water valve behind or under your refrigerator or under your sink.
• Turn the valve clockwise until it stops. This will shut off the water supply to your refrigerator.

How to Locate the Water Filter Housing

The water filter housing is where the water filter is installed. It is usually located behind the left side refrigerator door, near the top shelf.

• Open the refrigerator door and look for a small compartment with a push button on it.
• If you have a top shelf above the compartment, you may need to tilt it up and pull it out to access the compartment.

How to Remove the Old Water Filter

The old water filter needs to be removed before you can install a new one.

• Press the push button on the filter compartment and pull it down. This will lower the door of the compartment and expose the water filter.
• Pull the water filter downward and pull it gently towards you until it releases and pops out. There may be a small amount of water drainage when you do this. Use a paper towel or a cup to catch any waste.

How to Install the New Water Filter

The new water filter needs to be installed properly to ensure optimal performance.

• Open the new water filter by removing the plastic protective cover from it.
• Align the tabs on the side of the water filter with the holes on the manifold inside the filter compartment.
• Push the water filter into the manifold hole until it snaps in place. You may need to tilt it down slightly when pushing it in.
• Rotate the water filter up until it locks into position. You should hear a click sound when it’s done.
• Close the filter compartment door by lifting it up until it clicks.

How to Turn On the Water Valve

The water valve needs to be turned on again to restore the flow of water to your refrigerator.

• Locate the water valve behind or under your refrigerator or under your sink.
• Turn the valve counterclockwise until it stops. This will open up the water supply to your refrigerator.

How to Flush Out Air Bubbles

After installing a new water filter, you need to flush out any air bubbles that may be trapped in the system.

• Place a large container under the water dispenser and press and hold it for about 5 seconds.
• Release it for 5 seconds and repeat until you get a steady stream of water without any sputtering or spurting.
• Do this for about 2.5 gallons of water or until you no longer see any air bubbles in the dispensed water.

FAQs

Q: How often should I change my LG fridge water filter?

A: LG recommends changing your fridge water filter every six months or sooner if you notice a decrease in water pressure or a change in taste or odor. Your LG fridge will also indicate when you need to change your water filter by displaying a “Replace Filter” message on its control panel.

Q: What kind of water filter do I need for my LG fridge?

A: You need to use an LG brand water filter that is compatible with your fridge model. You can find out which one you need by checking your owner’s manual or visiting our Water Filter Finder page. Do not use non-LG brand or expired filters as they may not work properly or cause damage to your fridge.

Q: How do I reset my LG fridge after changing my water filter?

A: After changing your water filter, you may need to reset your LG fridge by pressing and holding a specific button on its control panel for about 3 seconds. This will clear any error codes or reminders related to your water filter. The button may vary depending on your fridge model, but it is usually marked with “Filter” or “Water” or has a water drop icon on it.

Changing the water filter on your LG fridge is a simple and important task that you can do yourself. By following these steps, you can ensure that you get clean and fresh water from your fridge dispenser and ice maker. You can also extend the life of your fridge and avoid any potential problems caused by a clogged or dirty water filter.