If you own a Frigidaire fridge, you may wonder how often and how to replace the water filter that ensures clean and fresh-tasting water and ice. Replacing the water filter is not a difficult task, but it does require some specific steps depending on the filter type and location. In this post, we will show you how to change the water filter in your Frigidaire fridge in 6 easy steps.
To replace the water filter in a Frigidaire fridge, you need to determine the filter type and locate it, turn off the power and water supply, remove the old filter, install the new filter, and run the water until it’s clear.
The first step is to identify what kind of water filter your Frigidaire fridge uses and where it is located. There are two main types of water filters: push-in filters and twist-in filters. Push-in filters are usually found in the back upper-right corner of the fridge interior, while twist-in filters are usually located in the grille at the base of the fridge.
To find out which type of filter you have, you can check your owner’s manual or visit the Frigidaire website and enter your model number. You can also look for a label or sticker on the filter itself that indicates the model number and replacement instructions.
Before you remove the old filter, you need to turn off the power and water supply to your fridge. This will prevent any leaks or spills that could damage your appliance or floor. To turn off the power, you can either unplug your fridge from the wall outlet or flip the circuit breaker that controls it. To turn off the water supply, you can either use a shut-off valve behind or below your fridge or turn off the main water valve for your house.
The next step is to remove the old filter from its holder. Depending on the type of filter you have, this may involve different methods:
Be careful not to spill any water that may be inside the filter or its holder. You can place a towel or a bowl under the filter to catch any drips.
Once you have removed the old filter, you can install the new one by following these steps:
Make sure that the new filter is securely installed and flush with its holder.
After installing the new filter, you need to run the water dispenser and/or ice maker for about 3 minutes or until the water runs clear. This will flush out any air bubbles or impurities that may be in the new filter or the water line. You may also notice some sputtering or noise during this process, which is normal.
You can discard the first batch of ice that is produced after replacing the filter, as it may contain some particles from the new filter.
The final step is to reset the filter status light on your fridge display panel. This light indicates when you need to replace your water filter based on your usage and water quality. To reset it, you need to press and hold a specific button for about 3 seconds or until the light turns green. The button may vary depending on your fridge model, but it is usually labeled as “Filter Reset” or “Water Filter”.
You can check your owner’s manual or visit https://support.frigidaire.com/Blog/Product-Advice–Education/How-to-Change-Water-Filters/ for more information on how to reset your filter status light.
Q: How often should I replace my Frigidaire water filter?
A: You should replace your Frigidaire water filter every 6 months or when the filter status light turns red. This will ensure optimal performance and quality of your water and ice.
Q: Where can I buy a replacement Frigidaire water filter?
A: You can buy a genuine Frigidaire water filter from https://www.frigidaire.com/Filters–Accessories/Filters/Water-Filters/ or from authorized retailers such as Amazon, Home Depot, or Lowe’s. Make sure to buy the correct filter model for your fridge and avoid counterfeit or generic filters that may not fit or work properly.
Q: How do I know if my Frigidaire water filter is working?
A: You can check if your Frigidaire water filter is working by tasting the water and ice from your fridge. If they taste fresh and clean, then your filter is working. If they taste stale, cloudy, or have an odor, then your filter may be clogged or expired and need to be replaced.
Replacing the water filter in your Frigidaire fridge is a simple and important task that can improve the quality and taste of your water and ice. By following the 6 steps above, you can easily change your water filter in less than 10 minutes and enjoy fresh and filtered water for months.
We hope this post has been helpful and informative for you. If you have any questions or comments, please feel free to leave them below. And don’t forget to check out our other blog posts on kitchen appliances and food safety at PressToCook.com!
